(updated tire rule 2/05/2012

Notice: All components are subject to inspection and approval of Track Officials. ALL RULES WILL BE INTERPRETED BY TRACK OFFICIALS. IF YOU HAVE ANY QUESTIONS ABOUT RULES, CALL BEFORE BUILDING CAR.

DRIVER RESTRAINT

1. Aluminum racing seat is required, with rib supports recommended. Seats must be securely mounted to chassis, not floor pan, with a minimum of four 3/8" bolts. Seat may not be positioned further back than doorpost.

2. 5 point safety harnesses are required. Required: S.F.I. tag must be legible. Must be bolted to the roll cage and frame with a minimum bolt size of ½ inch bolts.

3. A window net is Mandatory. No sprint car nets.

4. All helmets must be a full face, current Snell 90 or newer sticker in it. Snell SA90 & SA00 legal.

5. All drivers are required to wear a driving suit. No nomex coveralls will be allowed. Neck brace are mandatory for drivers. Driving gloves and driving shoes are required.

WEIGHT

2350 lbs. minimum

CARBURETOR

602 Crate engine ONLY can utilize a 650 cfm Holley carburetor P/N 80541-1

You may only run (1) carburetor on intake.

Chevrolet:  Holley #4412, or #0-80583-1 two barrels.

Ford: Holley #4412, or #0-80583-1 two barrels.

Mopar:  Holley #4412, or #0-80583-1 two barrels.

Carburetor spacer/adapter is allowed, but must not exceed 1-1/4 thickness including gaskets. Will check carb top and bottom.

Carburetor must be stock and unaltered with only one exception; circle track floats may be used. Holley must have choke horn attached.

No Edelbrock or similar hi-performance carburetors allowed.

ENGINE

Only cast iron OEM blocks can be used for GM. No big block. 368 CI maximum.

Only 260, 289, 302, and 351 blocks can be used for Ford. No big blocks. OEM only.

Only 273, 318, 340, and 360 blocks can be used for Mopar. No big blocks. OEM only. No Hemis.

All casting numbers must remain on blocks.

Mopar=Chrysler, Plymouth, and Dodge. 370 cubic inch maximum.

Pontiac, Buick, Oldsmobile as long as they are Chevrolet engines. 368 cubic inch maximum.

No tolerance on cubic inch.

Compression may not be over 180 lbs. per cylinder on any cylinder after 5 hits of starter. Tracks discretion on cylinders checked. No tolerance.

Pistons may be forged, must be stock appearing and 10 ½- 1 flattop, 2-valve or 4-valve relief . No light weight pistons.

Decking block okay. Maximum zero deck.

Stock OEM rods, or (stock appearing- no light weight and must be of "I-Beam" type). No aluminum. 5.7" length maximum rods are allowed.

OEM cranks only, steel or cast. Will allow stock appearing cast or steel aftermarket crankshafts. Cannot be lightened. Must be stock stroke for engine used. Maximum 350 stroke.

After-market rod, main and head bolts or studs allowed. Push rods may be any length.

Stock or circle track pans allowed. No dry sumps. No gas ported pistons. No accu. Sumps.

Fluid dampener harmonic balancers are allowed. No roller rod, main, or cam bearings.

OEM mechanically belt driven water pump only.

May use one of the following after-market aluminum intakes: Weiand GM #7547-1; Ford #7515, #8023 or #7516; Chrysler #7545; Edelbrock GM 2701.

No Brezenski, porting, polishing, acid dipping, or anything similar allowed. No hi-rise.

After market starters okay. Must mount in front of bell housing.

Power steering pump and reservoir must be a one-piece unit. Must mount in front of engine.

Steel side engine mounts may be of the 45 degree style or stock style.

Engine mid-plate is allowed and may be aluminum.

Any brand of air cleaner is allowed. No forced or RAM air allowed.

3.50 stroke maximum for Chevy. Balancing okay.

Engine displacement can be checked by pump even on protest.

Oil filters must attach at factory specs. No Oberg, etc. U. Polydyne coating or similar allowed.

Must have 1" sight plug in oil pan between the second and third pan bolt on the drivers side.

Sealed engine and GM factory seal bolts must remain intact and not show any evidence of tampering.

Any seal that is broken or shows evidence of tampering will disallow the engine.

The penalty for tampering, removing or modifying any of the parts of the engine may include suspension for up to one year, and/or loss of accumulated points and/or loss of purse and point fund monies.

Vacuum pumps NOT allowed.

CAMS

Conventional flat tappet cam and lifters allowed.No roller hyd or solid lifters cam or lifters allowed.Up to four bushings will be allowed for repair and lifter bore.No gear drives,no reverse rotation cams or motors,OEM rotation only.No vaccum rule,no fire order change.

HEADS

No porting, acid dipping, or polishing allowed. Screw-in studs and guide plates are legal.

Stock diameter springs only for heads used. Stock type rocker arms. Any ratio. Ford rocker arms on Chevrolet okay.

Flat milling okay. No angle milling.

 No aluminum nor titanium. Cast roller tip rockerarm allowed.

Poly-locks are allowed. Heads may be cut 360 degrees under valves in bowl area only.

No stud girdles. 1, 2, 3, 4, and 5 angle jobs are legal.

No jesel or other assemblies allowed. No O-ringing block or heads.

Any breather/valve cover configuration/composition allowed.

Due to Fords and mopars having no cc rule, neither will Chevy’s.

May use Engine Quest (EQ) stock replacement cylinder head, part number CH350I, head must remain as produced, seat angles and valve sizes cannot be changed; 3 angle valve job only (absolutely no casting removal in valve pocket of EQ head for any reason)

Chevrolet: Heads-GM

Only these casting numbers can be used: 997, 445, 882, 624, 441, 487, 993, 185. These are the last three digits and they are the only ones legal.

No valves larger than 1.94" intake or 1.5" exhaust. May remove smog clips inside exhaust ports. No X-heads.

Ford: Heads

Any cast iron head. OEM Ford heads only. Headers listed for Ford are the only headers that can be used. If the headers don’t fit the head you are using, head is illegal.

No boss or after-market heads of any kind.

No valves larger than 2.04 intake or 1.70 exhaust.

Mopar: Heads-Plymouth, Dodge, Chrysler

Any cast iron head. OEM Mopar only. Headers listed for Mopar are the only headers that can be used. If the header doesn’t fit head you are using, head is illegal.

No after-market heads of any kind.

No valves larger than 2.04 intake and 1.70 exhaust.

Mopar can use the rocker arm bars. OEM only. No roller tips.

ENGINE LOCATION

Back of entire flange must be mounted at a minimum of 70" forward of the centerline of the rear axle. This will be measured on the passenger side of the car.

Minimum engine height is 11" from the ground to the center of the crankshaft. This will be measured on the front of the crankshaft/pulley.

IGNITION

All cars must have ignition switch clearly labeled.

Ignition switch must be located within reach when standing outside the car(easily accessible to emergency personnel).

Stock or stock style ignition only. Ford may use Motorcraft, including box. Mopar may use Mopar, including box. HEI legal on Ford or Mopar.

HEI must remain in one unit, no external coils allowed, unless you are using dual or single point distributor.

MSD or any module may be used as long as it fits inside the distributor with no alteration. Vacuum advance may be removed and the pick-up coil locked.

MSD, any brand, or GM electronic boxes are not allowed. No magnetos.

BATTERY

Only (1) 12-volt battery is allowed and must be securely mounted. Subject to tech inspection. Battery may be charged by an alternator.

EXHAUST SYSTEM

Headers- any 1 5/8" tube 4 into 1 with 3" collector one-piece header. No 180 degree or step header must bolt directly to the head with no modifications or adapter. Mufflers are mandatory, no more than 100 dB at 100 feet.

RADIATOR

Only (1) radiator is allowed. It may be aluminum. Radiator must be mounted in front of engine. Maximum size; 27" X 19".

Racing radiator cap is allowed. Electric cooling fans are okay. May not have water outlets to spray on radiator. Catch cans are required.

FUEL

Gasoline only. No oxygenated or other performance enhancers. No alcohol or nitrous. Racing gasoline allowed.

FUEL PUMP

No electric fuel pumps. Only stock mount push rod activated Holley and Carter style allowed. No by-pass fuel systems, pressurized, or return lines allowed. No regulators of any type. Lever type fuel pumps only.

FUEL CELL

Maximum 22-gallon fuel cell. Fuel cell with a roll over valve is required. Must be securely mounted inside trunk area only, must be between frame rails, and must be totally enclosed from the driver compartment. A minimum of (2) fuel cell straps required to secure fuel cell. Fuel cell protection bar required. Must be a minimum of 1 1/2" X 0.95". It must protect the fuel cell from the rear. It must be as low as the fuel cell, and extend from side to side as wide as the fuel cell. It is recommended that this bar be attached to the frame, not the bumper. If the fuel cell protection bar is not present, the car will not be allowed to continue running.

TRANSMISSION

Any OEM automatic transmission is allowed. Must have a working torque converter, minimum of 10". No direct drives, couplers, valved pumps, or bleeder

style valve bodies. Automatics must have at least (1) forward gear, and reverse gear must be in working order. Ford may use GM or Ford automatic. Mopar may use GM or Mopar automatic. Chevrolet must use GM automatic. Stall converters okay.

Standard transmissions must be stock with all gears in working order, with minimum of 10.5" clutch, pressure plate and steel flywheel. No mini-clutches. May use aluminum flywheel. Ford clutch is 9" minimum.

All standards must have bell housing made of ¼" thick steel or cast iron and cover 180 degrees over the sides and tip of the clutch assembly. Slave cylinders or hydraulic throw out bearing okay.

Car must be self-starting and have working neutral, reverse, and forward (with engine running and car in a still position must be able to engage car in gear and move forward, then backwards).

Transmission fluid coolers are allowed.

DRIVE SHAFT

Drive shafts must be steel, and must be painted white or silver. Must have steel drive shaft loop (360 degree) connected to the frame located within 6" of the front drive shaft u-joint. Minimum size is 2" X 1/8".

REAR END

Rear end housing must be stock 7.5" GM 10 bolt. Bracing optional. Snouts on end of 7.5" rear end can be modified to accept 9" Ford axle. Stock mounts on lower trailing arms must remain in stock location on original 7.5" tube housing. No 3" tube from center section out to mounts on trailing arms. After-market axles, studs, and mini-spools are allowed. No posi-trac, limited slip style rear ends. Rear end axles must be locked together at all times. C-clip eliminators are allowed. Cups may be placed on housing for springs only.

Any gear ratio may be used, if no alteration to housing is required.

Bolt pattern on the axle/drums may be changed. Pinion angle may not be altered. No full spools, Gold Track, or aluminum spools of any kind. Stock width unless using Ford axles. If Ford axles are used, rear end must not be narrower than stock nor more than 3" wider.

C-clip eliminators and disc brakes are allowed and recommended to eliminate axles from sliding out.

No floater rear ends of any type. No 9" Ford or 8.5" rear ends allowed. 7.5" only.

BRAKES

Single or dual master cylinder after market brake pedal is allowed, or dual pedal with adjuster okay within driver’s reach. Rear brakes must be drum or disc up to 12" disc brakes. Steel only. Hats and steel rotors are legal on rear ends only. Hats must be steel. No single-phase rotors allowed.

Minimum of (3) working brakes is required. If using (3) brakes, the fourth brake components need not be present. Wheel shut-off valve must not be in driver compartment. Spindle must remain unaltered.

Cooling holes may not be drilled in any brake components.

No aluminum brake components allowed.

STEERING

Quick release steering wheel is mandatory.

Quick steer is optional. No chains or sprockets allowed in the steering system except D & M quick steer.

Steering left of drive train only. This means drive shaft.

Bump steer cannot be adjusted. Center link, inner tie rods, outer tie rods, or sleeves cannot be altered (must be OEM and in OEM stock location).

Power steering is allowed. Steering pump and reservoir must remain one unit.

No rack and pinion steering. Stock OEM steering gear box must be used. May not be moved.

Idler arms must remain in stock location.

SUSPENSION

IMCA TUBULAR UPPER CONTROL ARMS WILL BE PERMITTED (steel only and must be IMCA stamped, non-adjustable). Steel or alum.cross shaft allowed.

No traction control of any type.

Upper control arm brackets may be moved for caster and camber adjustment. Can not move lower A-frames. Must use stock lower control arms and brackets. Upper mounts may be modified, but must remain stock material.

Upper and lower control arm bushings may be after-market.

Sway bars (may be removed) and brackets must remain stock. Bushings may be after-market.

Racing springs are allowed. Steel only. No coil-overs. No jack bolts allowed.

Adjustable spring buckets are allowed. May drop rear spring buckets as long as they are in stock location.

Spindles and rotors must remain stock for 1978-1987 metric frame w/108" wheelbase. Ball-joints must remain stock appearing (may be welded in). No grinding or lightening parts. Bolt on spindle savers are legal.

No welding on spindles. Reaming spindles for ball joints okay.

5/8" studs are allowed in any bolt pattern.

All four rear-trailing arms must retain stock arms for metric frame used. Must remain stock in length. Must not compress or lengthen. Arms may be boxed or

strengthened. After-market bushings may be used. No spherical or ball bearing or Timken bearings anywhere on the cars suspension.

No suspension parts may be altered or lightened.

No aluminum parts allowed, other than bushings.

Each trailing arm must have bushings installed and in good working order.

Lower A-frame mounts may be notched for clearance.

SHOCKS

Shocks must be steel. Must use stock type shock ends. May weld or screw stock ends on shocks.

The stock shock frame mounts must be used in the original stock location.

One shock per wheel. May use spacers when mounting shocks.

Air shocks not allowed.

CHASSIS FRAME

Mid-sized GM 1978-1987 metric full frames only with 108" wheelbase as per OEM specifications of stock. All frame bolt holes must remain in stock location. Wheelbase will be checked with a minimum of 107" and maximum of 109".

Frame cannot be cut, bent, or altered to change suspension brackets, except upper control arm brackets on front end.

Front frame horns can be cut off in front of the steering box and idler arm.

Rear frame rails may be cut off behind upper shock mounts.

Replacement may be made with round, square, or rectangular tubing.

Front frame may be cut for radiator clearance.

Frame may be cut for seat clearance.

You cannot cut holes in frame to lighten it. Rust may be removed, in front of lower rear trailing arms and cleaned up on body mount holes.

Frame cannot be widened, narrowed, shortened, or lengthened.

Cross member mounts on frame for transmission may be removed, but cannot be farther forward than welds on frame.

If weights are used for ballast, weights must be painted white and number of car must be on weight. No mercury ballast or any similar type of ballast may be used. All weight must be securely fastened. Loss of weight will be cause for disqualification.

ROLL CAGE

Main roll cage must consist of continuous hoops not less than 1 ½" X 0.95". All welds must be complete. No brazing or soldering. No part of main cage may extend forward past rear motor plate. The main roll bar must not attach to the frame rearward of front edge of the rear tire.

Main roll bar and halo must be a minimum of 1" above the drivers helmet.

A minimum of (3) drivers door bars, and (2) passenger side door bars is required.

(4) bars, two per side, may extend from the main roll cage to the points on the main frame in front of the upper control arms.

(6) bars may extend from the main cage to the rear, X-bracing is allowed.

Door plates are MANDATORY (minimum 4" X 12").

Cages must be steel or chrome-moly.

NERF BARS

One single nerf bar between the front and rear wheels on each side of the car is allowed. Maximum size= 1 ½" X 0.95". They are to be attached to the cage at the front and rear sections of the nerf bar. No center supports are allowed on the nerf

bar. Nerf bars may not be outside of tires. All bumpers and nerf bars must be capped.

WINDSHIELD BARS

Minimum of (3) windshield bars 5/16" in diameter is required. Must be mounted in front of driver.

TIRES

Must use unaltered Hoosier 500 H or American Racer 500 with a durometer hardness of no less than 41.  Tires may be grooved and siphed.Hoosier 500M ok.

WHEELS

Only steel 15" X 8" RR bead-lock is allowed.

Wheel spacers, maximum 1", allowed. Any offset wheel allowed. 5/8" studs are allowed. Wheel spacers may be aluminum.

One-inch diameter lug nuts are required. Wheel adapters will be treated as spacers and may be aluminum.

INTERIOR

Oil and transmission fluid coolers are not allowed in drivers compartment. Floor in drivers compartment must be complete; therefore, there must be a floor pan under the drivers seat.

UPHOLSTERY

No upholstery allowed, other than driver’s seat cover. No plastic in driver’s compartment.

BODY

Roof rear sail panels are allowed one 90-degree bend along the top edge of the sail panel, but must be less than 1" wide. No Gremlin style roofs.

No more than 6" of total rake allowed on the body deck. A maximum of 3" of rake (of the 6" total) is allowed in the door section and a maximum of 3" of rake is allowed in the quarter panel section. If you keep the door section level, then you are only allowed 3" of rake in the quarter panel section.

Minimum ride height is 5" from ground to side frame rails.

Plastic body panels and plastic filler panels are not allowed.

No convertibles, unless special race.

Cars must have full deck interior from one side of the body to the other. Decks must be aluminum or sheet metal.

FENDERS

Quarter panels must be 90 degrees to the ground, with a maximum of a 45 degree bend 4" from the bottom of the doors and quarters and 2" on top.

FIREWALL

Must be metal or aluminum sized holes for throttle, etc. Firewall must be sealed from engine compartment.

FLOOR

Must be metal or aluminum. Must cover entire driver’s cockpit to front edge of seat.

BUMPERS

(2) bar front bumper is mandatory. Maximum size is = 1 ½" X 0.95".

One single bar rear bumper is required. Maximum size is = 1 ¾". The required fuel cell protection bar (maximum size = 1 ½" X 0.95") may be attached to the rear bumper.

HOOD

Must cover completely the top of engine and radiator.

Must extend from the nosepiece to the deck.

Hood may be made of metal, aluminum, or fiberglass.

Hood must provide a seal to the top of the engine compartment.

Cannot cover side of engine more than 5".

Hood scoops okay.

SPOILER

Rear spoiler is allowed, with a maximum use of material of 15", measured along the spoiler, from the deck to the top, not straight up and down. A maximum of four braces are allowed, one on each side, measuring a maximum of the angled height of the spoiler X 24" long. Only (1) spoiler is allowed. Aluminum or lexan okay. Spoiler may not go beyond back bumper. NO SPOILER ON ROOF.

*** General Rules for Track also apply to this class. ***